3336 - 2007

Home
Up
Buses For Sale
MCI 9 Conv List
MCI 102 Conv List
Raising a Roof
Limo Party Bus I
Limo Party Bus II
Next Level Coaches
N L C    7001
Suncruiser
Scenicruiser 4501
Stretched Van
Factory
Interior Samples
Vendor Page

07/03/2008 02:36 AM

3336 - 2007

Most Recent Images on Top ....

Below is 2-9-06 through 7-24-07

7-24-07










 


7-26-06

Dash Hand Rail installed, Stair Cover Dry fitted ready to install  floor mount brace  ...(down but not resting on anything )

Need to make and install stairway cover strap and floor brace yet . More wiring done on dash 

                                            Added Piping,
 

7-25-06


Door Panel and door handle recess panel installed, no piping around edges yet ...
 Stairway cover padded and upholstered
 

7-19-06


Dry fitting Back up monitor

7-17-06


Dry fitting : Inside recessed pocket  for door handle, door striker, working on floor stairway cover panel.

Cover panel.

7-14-06


Assist hand rail on door reconditioned, Built floor of stairway cover 

7-13-06


Installed bathroom door ,      and handle , with striker plate

First coat of primer sealer on Dash Board Defroster Ducts,

Fabricating components  and installing stairway cover  base

   Fiberglass pocket for inside Entrance  Door  handle  being fabricated,
 Inside upholstered entrance door cover, prepping  to install  ...

 

7-12-06


Fabricating Brackets for gas Spring mounting to hold bed up

Installed Piano Hinge fro bed 

7-11-06


Made pc. for back of table top, Cleaning and prepping driver floor, Installed computer access
door so as not to interfere with plumbing 

Entrance Door pocket for inside door handle, under construction 

7-6-06


   Gauges installed , Mirror controls mounted,  Panel for Rear camera LCD monitor

  Driver floor area,  Passenger Seat pedestal lowered, Platform to raise Driver seat pedestal   

New mold for Entrance Door pocket for door handle

"7-4-06"



Left and right mirrors fitted and mounted, turn signals polished and re-installed.  Mirror wiring ran to dash .
When reconditioning left headlight, bezel found it to be damaged, looking for a better bezel bucket to replace with .

7-3-06


Ramco sent the wrong Stainless Steel Screws and trim cut-out was wrong.,..  Insulated and replaced skin back

         Note the Base mounts were cut wrong to fit over trim , see right side after modifications we had correct cut out,
                 holes would not line up .


Newly rebuilt rub rail almost ready to install,



New Door Window installed 

6-30-06


New Ramco Mirrors just in ..receiving hasn't checked them in yet

6-27-06



 

6-16-06

New MCI parts,
Note: bent corners and they sent the wrong lower panel . but we feel we can still use the panels
we didn't order the one with space for the side rub rail at the bottom .

6-14-06


6-13-06

Painted with finished top coat


Cleaned and painted around generator,   Cleaned and painted horns, Steering Box cover panel , and Condenser door back panel

 

6-9-06

Box Covered in felt material

                                                                                                                        TV and Cover ring around TV installed
 
Shower door installed
 

6-8-06


Painted with primer , need to wait a couple of days then we paint with finish coat .


Installed floor access deck plates

 

6-02-06

Dash Console  being installed with new upholstery       

Corrected  steering column, dry fitted column to confirm fit ,  Dry fitting dash console and upholstering the dash Board and side switch console , the doors to cover heater area already covered .
Note: all dash console wiring checked, prepped  and ready to install new gauges 


 Front bumper and all fittings removed to clean and paint after dry fitting .          

6-1-06

Dash  console panel cut and dry fitted with gauges before laminating with burled walnut laminate... 



Cable cover and Heater cover box

Installed stainless steel bumper  tie down hooks,

 Installed bumper supports with rubber cushion,    Also note fiberglass Tire cover mounted behind bumper ,

 Cut Aluminum panel to install behind old condenser door

Ran exhaust pipe for generator , note flex pipe to help keep down vibrations

Newly upholstered door panel

 

 

5-26-06

note : New Aluminum panels on both sides of spare tire bay 


5-24-06

5/19/2006


Polished Stainless Steel Wheel Liners



5/4/2006




 

5-4-06




3/20/2006


 

3/8/2006


 

3/6/2006




 

 

 

 

 

3/2/2006


 

 


 

.





 

 




 

2/03/05


 

2/16/05


 

03/03/05





 

3/11/05



 

 

3/24/05



 

4/11/2005









 

4/15/05
 





 






 

 

 

4/30/2005


5/5/2005



5/12/2005

 

  

5/19/2005



5/26/2005

 






 

6/2/2005

 


 

6/14/2005




 

6/16/2005

 






 

6/24/2005

 



 

6/30/2005

 



 

7/6/2005   

 






 

7/7/2005

 



 

8/29/2005




 

9/8/2005

 




 

9/9/2005

 


 

9/16/2005

 







 

9/23/2005

 








 

9/30/2005

 




 

10/7/2005

 







 

10/14/2005

 



 

10/28/2005

 




 

1/20/2006

 

 

2/9/2006